In the Linux kernel, the following vulnerability has been resolved: misc: fastrpc: fix DMA address corruption due to find_vma misuse fastrpc_get_args() uses find_vma() to look up the VMA for a user-provided pointer and compute a DMA address offset. When the address falls in a gap before the returned VMA, (ptr & PAGE_MASK) - vma->vm_start underflows, corrupting the DMA address sent to the DSP. Replace find_vma() with vma_lookup(), which returns NULL when the address is not contained within any VMA. The `fastrpc_get_args()` function incorrectly calculates a Direct Memory Access (DMA) address offset for user-provided pointers. This can lead to an underflow, corrupting the DMA address sent to the Digital Signal Processor (DSP). This corruption could result in system instability or other undefined behavior. Red Hat severity: not rated. Weakness: CWE-191. Red Hat lists Red Hat Enterprise Linux 10; Red Hat Enterprise Linux 6; Red Hat Enterprise Linux 7; Red Hat Enterprise Linux 8; Red Hat Enterprise Linux 9 as not affected.

CVE-2026-53159

Unclassified

Jun 25, 2026

UnratedLinux Updated

fix NULL-deref of opinfo->conn in oplock/lease break notifiers

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix NULL-deref of opinfo->conn in oplock/lease break notifiers smb2_oplock_break_noti() and smb2_lease_break_noti() read opinfo->conn into a local with neither READ_ONCE() nor a NULL check. Both run from oplock_break() after opinfo_get_list() has dropped ci->m_lock, so a concurrent SMB2 LOGOFF (session_fd_check()) can set op->conn = NULL under ci->m_lock within that window. ksmbd_conn_r_count_inc(conn) then writes through NULL at offset 0xc4 -- a remotely triggerable oops. Guard both reads the way compare_guid_key() already does: read opinfo->conn with READ_ONCE() and return early if it is NULL, before allocating the work struct so nothing leaks. A NULL conn means the client is gone and the break is moot, so return 0; oplock_break() treats that as success and runs the normal teardown. This occurs because `opinfo->conn` is read without proper checks, allowing a concurrent Server Message Block (SMB2) LOGOFF to set `op->conn` to NULL. Successful exploitation leads to a kernel oops, resulting in a Denial of Service (DoS). Red Hat severity: not rated. Weakness: CWE-476. Red Hat lists Red Hat Enterprise Linux 10; Red Hat Enterprise Linux 6; Red Hat Enterprise Linux 7; Red Hat Enterprise Linux 8; Red Hat Enterprise Linux 9 as not affected.

Clamp HDMI HDCP2 rx_id_list read to buffer size

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Clamp HDMI HDCP2 rx_id_list read to buffer size [Why & How] During HDCP 2.x repeater authentication over HDMI, the driver reads the sink's RxStatus register and extracts a 10-bit message size field (max value 1023). This value is used as the read length for the ReceiverID list without being clamped to the size of the destination buffer rx_id_list[177]. A malicious HDMI repeater could advertise a message size larger than the buffer, causing an out-of-bounds write during the I2C read. Clamp the read length in mod_hdcp_read_rx_id_list() to the size of the rx_id_list buffer, matching the approach already used in the DP branch. (cherry picked from commit 229212219e4247d9486f8ba41ef087358490be09) This could lead to an out-of-bounds write, potentially causing a denial of service or other unpredictable system behavior. Red Hat severity: not rated. Weakness: CWE-787. Red Hat lists Red Hat Enterprise Linux 10; Red Hat Enterprise Linux 6; Red Hat Enterprise Linux 7; Red Hat Enterprise Linux 8; Red Hat Enterprise Linux 9 as not affected.

Skip CSD when it has zeroed workgroups

In the Linux kernel, the following vulnerability has been resolved: drm/v3d: Skip CSD when it has zeroed workgroups A compute shader dispatch encodes its workgroup counts in the CFG0..CFG2 registers. Kicking off a dispatch with a zero count in any of the three dimensions is invalid. First, the hardware will process 0 as 65536, while the user-space driver exposes a maximum of 65535. Over that, a submission with a zeroed workgroup dimension should be a no-op. These zeroed counts can reach the dispatch path through an indirect CSD job, whose workgroup counts are only known once the indirect buffer is read and may legitimately be zero, but such scenario should only result in a no-op. Overwrite the indirect CSD job workgroup counts with the indirect BO ones, even if they are zeroed, and don't submit the job to the hardware when any of the workgroup counts is zero, so the job completes immediately instead of running the shader. A flaw was found in the Linux kernel's graphics driver for Broadcom V3D (VideoCore V) GPUs. This vulnerability occurs when a compute shader dispatch (CSD) is initiated with zero workgroup counts, which the hardware could misinterpret as a very large number. This misinterpretation could lead to unexpected system behavior or a denial of service (DoS), where the system becomes unresponsive or crashes. Red Hat severity: not rated. Weakness: CWE-1284.

fix use-after-free of a deferred file_lock on double SMB2_CANCEL

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix use-after-free of a deferred file_lock on double SMB2_CANCEL A deferred byte-range lock (an SMB2_LOCK that blocks) registers an async work on conn->async_requests via setup_async_work(), with cancel_fn = smb2_remove_blocked_lock and cancel_argv[0] pointing at the struct file_lock. When the request is cancelled, the worker frees the file_lock with locks_free_lock() and takes the cancelled early-exit, which "goto out"s and never reaches release_async_work() -- the only site that unlinks the work from conn->async_requests and clears cancel_fn/cancel_argv.

fix use-after-free of fastrpc_user in workqueue context

In the Linux kernel, the following vulnerability has been resolved: misc: fastrpc: fix use-after-free of fastrpc_user in workqueue context There is a race between fastrpc_device_release() and the workqueue that processes DSP responses. When the user closes the file descriptor, fastrpc_device_release() frees the fastrpc_user structure. Concurrently, an in-flight DSP invocation can complete and fastrpc_rpmsg_callback() schedules context cleanup via schedule_work(&ctx->put_work). If the workqueue runs fastrpc_context_free() in parallel with or after fastrpc_device_release() has freed the user structure, it dereferences the freed fastrpc_user. Depending on the state of the context at the time of the race, any one of the following accesses can be hit: 1. fastrpc_buf_free() calls fastrpc_ipa_to_dma_addr(buf->fl->cctx, ...) to strip the SID bits from the stored IOVA before passing the physical address to dma_free_coherent(). 2. fastrpc_free_map() reads map->fl->cctx->vmperms[0].vmid to reconstruct the source permission bitmask needed for the qcom_scm_assign_mem() call that returns memory from the DSP VM back to HLOS. 3. fastrpc_free_map() acquires map->fl->lock to safely remove the map node from the fl->maps list.

avoid potential null folio->mapping deref during error reporting

In the Linux kernel, the following vulnerability has been resolved: iomap: avoid potential null folio->mapping deref during error reporting When a buffered read fails, iomap_finish_folio_read() reports the error with fserror_report_io(folio->mapping->host, ...). This is called after ifs->read_bytes_pending has been decremented by the bytes attempted to be read. For a folio split across multiple read completions, the folio is only guaranteed to stay locked while read_bytes_pending > 0. Once iomap_finish_folio_read() decrements read_bytes_pending, another in-flight read can complete and end the read on the folio, which unlocks it. This allows truncate logic to run and detach the folio (set folio->mapping to NULL). As reported by Sam Sun, this is the race that can occur: CPU0: failed completion CPU1: final completion CPU2: truncate ----------------------- ---------------------- -------------- read_bytes_pending -= len finished = false /* preempted before fserror_report_io() */ read_bytes_pending -= len finished = true folio_end_read() truncate clears folio->mapping fserror_report_io( folio->mapping->host, ...) ^ NULL deref Fix this by reporting the error first before decrementing ifs->read_bytes_pending. A race condition can occur during buffered read error reporting, specifically in the `iomap_finish_folio_read()` function.

fix OOB write in ethosu_gem_cmdstream_copy_and_validate

In the Linux kernel, the following vulnerability has been resolved: accel/ethosu: fix OOB write in ethosu_gem_cmdstream_copy_and_validate() The command stream parsing loop increments the index variable a second time when a 64-bit command word is encountered (bit 14 set), but does not re-check the loop bound before writing the second word: for (i = 0; i < size / 4; i++) { bocmds[i] = cmds[0]; if (cmd & 0x4000) { i++; bocmds[i] = cmds[1]; /* unchecked */ } } The buffer bocmds is backed by a DMA allocation of exactly size bytes from drm_gem_dma_create(ddev, size), giving valid indices [0, size/4-1]. When i == size/4 - 1 on entry to an iteration and bit 14 of cmds[0] is set, bocmds[size/4-1] is written in bounds, i is then incremented to size/4, and bocmds[size/4] writes four bytes past the end of the allocation. Userspace controls both the buffer contents and the size argument via the ioctl, making this a userspace-triggerable heap out-of-bounds write. Fix by checking the incremented index against the buffer bound before the second write and returning -EINVAL if the buffer is too small to contain the extended command. A local user can exploit this vulnerability by providing a specially crafted command stream, which causes an out-of-bounds write in memory.

Fix use-after-free in metadata dst teardown

In the Linux kernel, the following vulnerability has been resolved: net: airoha: Fix use-after-free in metadata dst teardown airoha_metadata_dst_free() runs metadata_dst_free() which frees the metadata_dst with kfree() immediately, bypassing the RCU grace period. In the RX path, skb_dst_set_noref() sets a non-refcounted pointer from the skb to the metadata_dst. This function requires RCU read-side protection and the dst must remain valid until all RCU readers complete. Since metadata_dst_free() calls kfree() directly, an use-after-free can occur if any skb still holds a noref pointer to the dst when the driver tears it down. Replace metadata_dst_free() with dst_release() which properly goes through the refcount path: when the refcount drops to zero, it schedules the actual free via call_rcu_hurry(), ensuring all RCU readers have completed before the memory is freed. A flaw was found in the Linux kernel's airoha network driver. This use-after-free vulnerability occurs when the `airoha_metadata_dst_free()` function frees memory prematurely, before all references to it are released. If a network packet still holds a pointer to the freed memory, a use-after-free condition can arise. This could lead to system instability or potentially allow an attacker to escalate privileges. Red Hat severity: not rated. Weakness: CWE-911.

fix arithmetic issues in dma_length

In the Linux kernel, the following vulnerability has been resolved: accel/ethosu: fix arithmetic issues in dma_length() dma_length() derives DMA region usage from command stream values and updates region_size[]: len = ((len + stride[0]) * size0 + stride[1]) * size1 region_size[region] = max(..., len + dma->offset) Several arithmetic issues can corrupt the derived region size: - signed stride values may underflow when added to len - intermediate multiplications may overflow - len + dma->offset may overflow during region_size updates - dma_length() error returns were not validated by the caller region_size[] is later used by ethosu_job.c to validate command stream accesses against GEM buffer sizes. Arithmetic wraparound can therefore under-report region usage and bypass the bounds validation. The dma_length() function, responsible for calculating Direct Memory Access (DMA) region usage, contains several arithmetic issues. These issues, including potential underflows and overflows during calculations, can lead to an under-reporting of memory region sizes. This under-reporting can bypass crucial bounds validation checks, potentially allowing an attacker to access memory outside of its intended boundaries. Red Hat severity: not rated. Weakness: CWE-190.

reject NPU_OP_RESIZE commands from userspace

In the Linux kernel, the following vulnerability has been resolved: accel/ethosu: reject NPU_OP_RESIZE commands from userspace NPU_OP_RESIZE is a U85-only command that the driver does not yet implement. The existing WARN_ON(1) placeholder fires unconditionally whenever userspace submits this command via DRM_IOCTL_ETHOSU_GEM_CREATE, causing unbounded kernel log spam. If panic_on_warn is set the kernel panics, giving any unprivileged user with access to the DRM device a trivial denial-of-service primitive. Replace the WARN_ON(1) with an explicit -EINVAL return so the ioctl rejects the command before it reaches hardware. An unprivileged local user with access to the Direct Rendering Manager (DRM) device could submit a specific command (`NPU_OP_RESIZE`) that the driver does not properly handle. This could lead to excessive kernel log spam and, if the `panic_on_warn` setting is enabled, cause the kernel to crash, resulting in a denial of service (DoS). Red Hat severity: not rated. Weakness: CWE-617. Red Hat lists Red Hat Enterprise Linux 10; Red Hat Enterprise Linux 6; Red Hat Enterprise Linux 7; Red Hat Enterprise Linux 8; Red Hat Enterprise Linux 9 as not affected.

Fix NULL pointer dereference in rpmsg callback

In the Linux kernel, the following vulnerability has been resolved: misc: fastrpc: Fix NULL pointer dereference in rpmsg callback A NULL pointer dereference was observed on Hawi at boot when the DSP sends a glink message before fastrpc_rpmsg_probe() has completed initialization: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000178 pc : _raw_spin_lock_irqsave+0x34/0x8c lr : fastrpc_rpmsg_callback+0x3c/0xcc [fastrpc] ... Call trace: _raw_spin_lock_irqsave+0x34/0x8c (P) fastrpc_rpmsg_callback+0x3c/0xcc [fastrpc] qcom_glink_native_rx+0x538/0x6a4 qcom_glink_smem_intr+0x14/0x24 [qcom_glink_smem] The faulting address 0x178 corresponds to the lock variable inside struct fastrpc_channel_ctx, confirming that cctx is NULL when fastrpc_rpmsg_callback() attempts to take the spinlock. There are two issues here. First, dev_set_drvdata() is called before spin_lock_init() and idr_init(), leaving a window where the callback can retrieve a valid cctx pointer but operate on an uninitialized spinlock. Second, the rpmsg channel becomes live as soon as the driver is bound, so fastrpc_rpmsg_callback() can fire before dev_set_drvdata() is called at all, resulting in dev_get_drvdata() returning NULL.

prevent use-after-free when the client exits before the supplicant

In the Linux kernel, the following vulnerability has been resolved: tee: optee: prevent use-after-free when the client exits before the supplicant Commit 70b0d6b0a199 ("tee: optee: Fix supplicant wait loop") made the client wait as killable so it can be interrupted during shutdown or after a supplicant crash. This changes the original lifetime expectations: the client task can now terminate while the supplicant is still processing its request. If the client exits first it removes the request from its queue and kfree()s it, while the request ID remains in supp->idr. A subsequent lookup on the supplicant path then dereferences freed memory, leading to a use-after-free. Serialise access to the request with supp->mutex: * Hold supp->mutex in optee_supp_recv() and optee_supp_send() while looking up and touching the request. * Let optee_supp_thrd_req() notice that the client has terminated and signal optee_supp_send() accordingly. With these changes the request cannot be freed while the supplicant still has a reference, eliminating the race. A flaw was found in the Linux kernel's Trusted Execution Environment (TEE) subsystem, specifically within the OP-TEE driver. This use-after-free vulnerability occurs when a client task terminates before its associated supplicant has finished processing a request.

Fix use-after-free during device removal

In the Linux kernel, the following vulnerability has been resolved: net: ibm: emac: Fix use-after-free during device removal The driver was using devm_register_netdev() which causes unregister_netdev() to be deferred until the devres cleanup phase, which runs after emac_remove() returns. This creates a use-after-free window where: 1. emac_remove() is called, which tears down hardware (cancels work, detaches modules, unregisters from MAL) 2. emac_remove() returns 3. devres cleanup runs and finally calls unregister_netdev() During step 3, the network stack might still process packets, triggering emac_irq(), emac_poll(), or other handlers that access now-freed hardware resources (dev->emacp, dev->mal, etc.). Fix this by replacing devm_register_netdev() with manual register_netdev() and calling unregister_netdev() at the beginning of emac_remove(), before any hardware teardown. This ensures the network device is fully stopped and unregistered before hardware resources are released.

refill RX buffers before XDP or skb use

In the Linux kernel, the following vulnerability has been resolved: net: mvpp2: refill RX buffers before XDP or skb use The RX error path returns the current descriptor buffer to the hardware BM pool. That is only valid while the driver still owns the buffer. mvpp2_rx_refill() can fail after the current buffer has been handed to XDP or attached to an skb. In those cases mvpp2_run_xdp() may have recycled, redirected, or queued the page for XDP_TX, and an skb free also retires the data buffer. Returning such a buffer to BM lets hardware DMA into memory that is no longer owned by the RX ring. If the allocation fails there, drop the packet and return the still-owned current buffer to BM, preserving the pool depth. Once the refill succeeds, later local drops retire/free the current buffer instead of returning it to BM. A flaw was found in the Linux kernel's mvpp2 network driver. This vulnerability occurs due to incorrect handling of receive (RX) buffers, where a buffer is returned to the hardware Buffer Manager (BM) pool after it has been passed to the eXpress Data Path (XDP) or attached to a socket buffer (skb). This allows hardware Direct Memory Access (DMA) operations into memory that is no longer controlled by the RX ring, potentially leading to memory corruption. Red Hat severity: not rated. Weakness: CWE-763.

fix use-after-free on first_skb in __input_process_payload

In the Linux kernel, the following vulnerability has been resolved: xfrm: iptfs: fix use-after-free on first_skb in __input_process_payload __input_process_payload() stores first_skb into xtfs->ra_newskb under drop_lock when starting partial reassembly, then unlocks and breaks out of the processing loop. The post-loop check reads xtfs->ra_newskb without the lock to decide whether first_skb is still owned: if (first_skb && first_iplen && !defer && first_skb != xtfs->ra_newskb) Between spin_unlock and this read, a concurrent CPU running iptfs_reassem_cont() (or the drop_timer hrtimer) can complete reassembly, NULL xtfs->ra_newskb, and free the skb. The check then evaluates first_skb != NULL as true, and pskb_trim/ip_summed/consume_skb operate on the freed skb — a use-after-free in skbuff_head_cache. Replace the unlocked read with a local bool that records whether first_skb was handed to the reassembly state in the current call. The flag is set after the existing spin_unlock, before the break, using the pointer equality that is stable at that point (first_skb == skb iff first_skb was stored in ra_newskb). A race condition during partial packet reassembly in the __input_process_payload() function can lead to a use-after-free vulnerability. This occurs when a concurrent process frees a packet buffer (skb) before it is checked, allowing subsequent operations to access freed memory.

Fix using an uninitialized stack variable in rseq_exit_user_update

In the Linux kernel, the following vulnerability has been resolved: rseq: Fix using an uninitialized stack variable in rseq_exit_user_update() There is an bug in which an uninitialized stack variable is used in rseq_exit_user_update() as reported by syzbot: BUG: KMSAN: kernel-infoleak in rseq_set_ids_get_csaddr include/linux/rseq_entry.h:502 [inline] The local variable: struct rseq_ids ids = { .cpu_id = task_cpu(t), .mm_cid = task_mm_cid(t), .node_id = cpu_to_node(ids.cpu_id), }; According to the C standard, the evaluation order of expressions in an initializer list is indeterminately sequenced. The compiler (Clang, in this KMSAN build) evaluates `cpu_to_node(ids.cpu_id)` *before* `ids.cpu_id` is initialized with `task_cpu(t)`. This is fixed by moving the assignment of ids.node_id outside the structure initialization. An uninitialized stack variable in the `rseq_exit_user_update()` function can lead to an information leak. This occurs due to an indeterminate sequencing of expressions during the initialization of the `rseq_ids` structure, where `ids.node_id` is assigned using an uninitialized `ids.cpu_id`. A local attacker could potentially exploit this to gain sensitive kernel information. Red Hat severity: not rated. Weakness: CWE-908.

CVE-2026-53243

Unclassified

Jun 25, 2026