Red Hat Linux Linux Kernel Vulnerabilities & Security Advisories
2150 advisories tracked · Red Hat Security Data API · 1 listed in the CISA Known Exploited Vulnerabilities catalog
Every row below is a published Red Hat Linux advisory that VulniPulse classified as Linux Kernel, with the CVEs, affected and fixed releases and exploitation status the vendor stated. Severity mix: 782 high, 1365 medium, 1 low.
Android app · Google Play
Monitor Red Hat CVEs from your phone.
Choose a whole vendor or a precise platform, then receive matching security advisories by phone notification, email, or both. Coverage follows 32 official vendor sources and 160+ reviewed platform categories.
Source
Red Hat Security Data API
Red Hat Enterprise Linux errata (RHSA) via the official Red Hat Security Data API — CVE severity, CVSS and affected packages. A credential-free official source.
Latest Red Hat Linux Kernel advisories
High [CVE-2026-64189] fix race between dump and ip_set_list resize
In the Linux kernel, the following vulnerability has been resolved: netfilter: ipset: fix race between dump and ip_set_list resize The release path of ip_set_dump_do() and ip_set_dump_done() read inst->ip_set_list via ip_set_ref_netlink(), a plain rcu_dereference_raw() of the array pointer. These run from netlink_recvmsg() without the nfnl mutex and without an RCU read-side critical section. A concurrent ip_set_create() can grow the array: it publishes the new array, calls synchronize_net() and then kvfree()s the old one. Since the dump paths read the array outside any RCU reader, synchronize_net() does not wait for them and the old array can be freed while they still index into it, causing a use-after-free. The dumped set itself stays pinned via set->ref_netlink, so only the array load needs protecting. Take rcu_read_lock() around it, matching ip_set_get_byname() and __ip_set_put_byindex(). BUG: KASAN: slab-use-after-free in ip_set_dump_do (net/netfilter/ipset/ip_set_core.c:1697) Read of size 8 at addr ffff88800b5c4018 by task exploit/150 Call Trace:... kasan_report (mm/kasan/report.c:595) ip_set_dump_do (net/netfilter/ipset/ip_set_core.c:1697) netlink_dump (net/netlink/af_netlink.c:2325) netlink_recvmsg (net/netlink/af_netlink.c:1976) sock_recvmsg (net/socket.c:1159) __sys_recvfrom (net/socket.c:2315)...
Medium [CVE-2026-64206] cancel pending_rx_work before taking conn->lock
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: L2CAP: cancel pending_rx_work before taking conn->lock l2cap_conn_del() takes conn->lock and then calls cancel_work_sync() for pending_rx_work. process_pending_rx() takes the same mutex, so teardown can deadlock against the worker it is flushing. This issue was found by our static analysis tool and then manually reviewed against the current tree. The grounded PoC kept the l2cap_conn_ready() -> queue_work(..., &conn->pending_rx_work) submit path, the l2cap_conn_del() -> cancel_work_sync(&conn->pending_rx_work) teardown path, and the process_pending_rx() -> mutex_lock(&conn->lock) worker edge. Lockdep WARNING: possible circular locking dependency detected process_pending_rx+0x21/0x2a [vuln_msv] l2cap_conn_del.constprop.0+0x3f/0x4e [vuln_msv] *** DEADLOCK *** Cancel pending_rx_work before taking conn->lock, matching the existing lock-before-drain ordering used for the two delayed works in the same teardown path. The pending_rx queue is still purged after the work has been cancelled and conn->lock has been acquired. A flaw was found in the Linux kernel's Bluetooth Logical Link Control and Adaptation Protocol (L2CAP) subsystem. A local attacker could trigger a deadlock during connection teardown due to a circular locking dependency between `l2cap_conn_del()` and `process_pending_rx()` functions.
Medium [CVE-2026-64190] fix NULL pointer dereference in team_xmit during mode change
In the Linux kernel, the following vulnerability has been resolved: net: team: fix NULL pointer dereference in team_xmit during mode change __team_change_mode() clears team->ops with memset() before restoring safe dummy handlers via team_adjust_ops(). A concurrent team_xmit() running under RCU on another CPU can read team->ops.transmit during this window and call a NULL function pointer, crashing the kernel. The race requires a mode change (CAP_NET_ADMIN) concurrent with transmit on the team device. BUG: kernel NULL pointer dereference, address: 0000000000000000 Oops: 0010 [#1] SMP KASAN NOPTI RIP: 0010:0x0 Call Trace: team_xmit (drivers/net/team/team_core.c:1853) dev_hard_start_xmit (net/core/dev.c:3904) __dev_queue_xmit (net/core/dev.c:4871) packet_sendmsg (net/packet/af_packet.c:3109) __sys_sendto (net/socket.c:2265) The original code assumed that no ports means no traffic, so mode changes could freely memset()/memcpy() the ops. AF_PACKET with forced carrier breaks that assumption. Prevent the race instead of making it safe: replace memset()/memcpy() with per-field updates that never touch transmit or receive. Those two handlers are managed solely by team_adjust_ops(), which already installs dummies when tx_en_port_count == 0 (always true during mode change since no ports are present).
Medium [CVE-2026-64187] fail recovery on a committed log item with no regions
In the Linux kernel, the following vulnerability has been resolved: xfs: fail recovery on a committed log item with no regions If the first op of a transaction is a bare transaction header (len == sizeof(struct xfs_trans_header)), xlog_recover_add_to_trans() adds an item but no region, leaving it on r_itemq with ri_cnt == 0 and ri_buf == NULL. The header can be split across op records, so later ops may still add regions; the item is only invalid if the transaction commits with none. The runtime commit path never emits such a transaction, so this only happens on a crafted log. It came from an AI-assisted code audit of the recovery parser. xlog_recover_reorder_trans() calls ITEM_TYPE() on the item, which reads *(unsigned short *)item->ri_buf[0].iov_base and faults on the NULL ri_buf. Reject it there, before the commit handlers that also read ri_buf[0]. Affected products named by the advisory: Red Hat Enterprise Linux 10; Red Hat Enterprise Linux 6; Red Hat Enterprise Linux 7; Red Hat Enterprise Linux 8; and 2 more.
Medium [CVE-2026-64205] fix hardware state machine corruption in error path
In the Linux kernel, the following vulnerability has been resolved: i2c: i801: fix hardware state machine corruption in error path A severe livelock and subsequent Hung Task panic were observed in the i2c-i801 driver during concurrent Fuzzing. The crash is caused by an unconditional hardware register cleanup in the error handling path of i801_access(). When i801_check_pre() fails (e.g., returning -EBUSY because the SMBus controller is actively used by BIOS/ACPI), the kernel does not actually acquire the hardware ownership. However, the code jumps to the 'out' label and executes: iowrite8(SMBHSTSTS_INUSE_STS | STATUS_FLAGS, SMBHSTSTS(priv)); This forcefully clears the INUSE_STS lock and resets the hardware status flags without owning the controller. Doing so interrupts ongoing BIOS/ACPI transactions and totally corrupts the SMBus hardware state machine. Consequently, all subsequent i801_access() calls fail at the pre-check stage, triggering an endless stream of "SMBus is busy, can't use it!" error logs. Over a slow serial console, this printk flood monopolizes the CPU (Console Livelock), starving other processes trying to acquire the mmap_lock down_read semaphore, ultimately triggering the hung task watchdog. Fix this by moving the 'out' label below the hardware register cleanup.
High [CVE-2026-64098] use uninterruptible resv lock for plane updates
In the Linux kernel, the following vulnerability has been resolved: drm/virtio: use uninterruptible resv lock for plane updates virtio_gpu_cursor_plane_update() and virtio_gpu_resource_flush() lock the framebuffer BO's dma_resv via virtio_gpu_array_lock_resv() and ignore its return value. The function can fail with -EINTR from dma_resv_lock_interruptible() (signal during lock wait) or with -ENOMEM from dma_resv_reserve_fences() (fence slot allocation), leaving the resv lock not held. The queue path then walks the object array and calls dma_resv_add_fence(), which requires the lock held; with lockdep enabled this trips dma_resv_assert_held(): WARNING: drivers/dma-buf/dma-resv.c:296 at dma_resv_add_fence+0x71e/0x840 Call Trace: virtio_gpu_array_add_fence virtio_gpu_queue_ctrl_sgs virtio_gpu_queue_fenced_ctrl_buffer virtio_gpu_cursor_plane_update drm_atomic_helper_commit_planes drm_atomic_helper_commit_tail commit_tail drm_atomic_helper_commit drm_atomic_commit drm_atomic_helper_update_plane __setplane_atomic drm_mode_cursor_universal drm_mode_cursor_common drm_mode_cursor_ioctl drm_ioctl __x64_sys_ioctl Beyond the WARN, mutating the dma_resv fence list without the lock races with concurrent readers/writers and can corrupt the list. Affected products named by the advisory: Red Hat Enterprise Linux 10; Red Hat Enterprise Linux 9; Red Hat package: kernel-rt.
High [CVE-2026-64069] Fix cancellation of a DIO and single read subrequests
In the Linux kernel, the following vulnerability has been resolved: netfs: Fix cancellation of a DIO and single read subrequests When the preparation of a new subrequest for a read fails, if the subrequest has already been added to the stream->subrequests list, it can't simply be put and abandoned as the collector may see it. Also, if it hasn't been queued yet, it has two outstanding refs that both need to be put. Both DIO read and single-read dispatch fail at this; further, both differ in the order they do things to the way buffered read works. Fix cancellation of both DIO-read and single-read subrequests that failed preparation by the following steps: (1) Harmonise all three reads (buffered, dio, single) to queue the subreq before prepping it. (2) Make all three call netfs_queue_read() to do the queuing. (3) Set NETFS_RREQ_ALL_QUEUED independently of the queuing as we don't know the length of the subreq at this point. (4) In all cases, set the error and NETFS_SREQ_FAILED flag on the subreq and then call netfs_read_subreq_terminated() to deal with it. This will pass responsibility off to the collector for dealing with it. This can lead to resource leaks or unexpected behavior, potentially impacting system stability. Red Hat severity: Moderate — CVSS 7 (CVSS:3.1/AV:L/AC:H/PR:L/UI:N/S:U/C:H/I:H/A:H). Weakness: CWE-772. Affected Red Hat products: Red Hat Enterprise Linux 10.
High [CVE-2026-64176] fix driver-set TX rates on old devices
In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: fix driver-set TX rates on old devices On old devices such as 7265D, rates are still encoded in version 1 format, which doesn't use the CCK/OFDM rate index (0-3/0-7) but rather their PLCP value (e.g. 10 for 1 Mbps CCK rate.) While introducing v3 rates, I changed the driver from internally handling v1 rates and converting to v2, to internally handling v3 and converting to v1 or v2 according to the firmware. I accordingly changed the code in iwl_mvm_mac80211_idx_to_hwrate() to no longer have different values for different APIs. This was correct. However, I later reverted this part of the change, because it was reported that I had broken beacon rates, causing a FW assert/crash. This caused TX_CMD rates to be set incorrectly, potentially causing a warning when reported back from the device as having been used. Fix this (hopefully correctly now) by handling beacon rates in the TX_CMD that's embedded in the beacon template command separately. Restore iwl_mvm_mac80211_idx_to_hwrate() to return only the rate index, not PLCP value, fixing the real TX_CMD. A flaw was found in the Linux kernel's iwlwifi driver, affecting older Intel wireless devices. This vulnerability arises from incorrect handling of transmit (TX) rates, specifically when the driver attempts to set these rates.
High [CVE-2026-64152] Handle unmap error when iommu_debug is enabled
In the Linux kernel, the following vulnerability has been resolved: iommu: Handle unmap error when iommu_debug is enabled Sashiko noticed a latent bug where the map error flow called iommu_unmap() which calls iommu_debug_unmap_begin()/iommu_debug_unmap_end() however since this is an error path the map flow never actually established the original iommu_debug_map() it will malfunction. Lift the unmap error handling into iommu_map_nosync() and reorder it so the trace_map()/iommu_debug_map() records the partial mapping and then immediately unmaps it. This avoid creating the unbalanced tracking and provides saner tracing instead of a unmap unmatched to any map. A flaw was found in the Linux kernel's Input/Output Memory Management Unit (IOMMU) subsystem when `iommu_debug` is enabled. This issue occurs because an error handling path attempts to unmap memory without a proper initial mapping, leading to an inconsistent state within the IOMMU's debugging and tracing mechanisms. This malfunction could result in unbalanced tracking, potentially affecting system stability or the accuracy of IOMMU debugging information. Red Hat severity: Moderate — CVSS 7.1 (CVSS:3.1/AV:L/AC:L/PR:L/UI:N/S:U/C:H/I:N/A:H). Weakness: CWE-832. Affected Red Hat products: Red Hat Enterprise Linux 10. Red Hat does not currently list a fixing RHSA for this CVE.
High [CVE-2026-64174] advance loop vars in cfg80211_merge_profile
In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: advance loop vars in cfg80211_merge_profile() cfg80211_merge_profile() reassembles a Multi-BSSID non-transmitted BSS profile that has been split across multiple consecutive MBSSID elements. Its while-loop calls cfg80211_get_profile_continuation(ie, ielen, mbssid_elem, sub_elem) but never advances mbssid_elem or sub_elem inside the body. Each iteration therefore searches for a continuation that follows the same fixed pair; the helper returns the same next_mbssid; and the same next_sub bytes are memcpy()'d into merged_ie at a growing offset until the buffer fills. Advance both mbssid_elem and sub_elem to the just-consumed continuation so the next call to cfg80211_get_profile_continuation() searches for a further continuation beyond it (or returns NULL when none exists). A specially-crafted malicious beacon can take advantage of this bug to cause the kernel to spend an excessive amount of time in cfg80211_merge_profile (up to as much as 2ms per beacon received), which could theoretically be abused in some way. A remote attacker, by sending a specially-crafted malicious Wi-Fi beacon, could exploit a vulnerability in the cfg80211_merge_profile() function. This flaw causes the kernel to spend an excessive amount of processing time, leading to a Denial of Service (DoS) condition.
High [CVE-2026-64061] Fix early put of sink folio in netfs_read_gaps
In the Linux kernel, the following vulnerability has been resolved: netfs: Fix early put of sink folio in netfs_read_gaps() Fix netfs_read_gaps() to release the sink page it uses after waiting for the request to complete. The way the sink page is used is that an ITER_BVEC-class iterator is created that has the gaps from the target folio at either end, but has the sink page tiled over the middle so that a single read op can fill in both gaps. The bug was found by KASAN detecting a UAF on the generic/075 xfstest in the cifsd kernel thread that handles reception of data from the TCP socket: BUG: KASAN: use-after-free in _copy_to_iter+0x48a/0xa20 Write of size 885 at addr ffff888107f92000 by task cifsd/1285 CPU: 2 UID: 0 PID: 1285 Comm: cifsd Not tainted 7.0.0 #6 PREEMPT(lazy) Call Trace: dump_stack_lvl+0x5d/0x80 print_report+0x17f/0x4f1 kasan_report+0x100/0x1e0 kasan_check_range+0x10f/0x1e0 __asan_memcpy+0x3c/0x60 _copy_to_iter+0x48a/0xa20 __skb_datagram_iter+0x2c9/0x430 skb_copy_datagram_iter+0x6e/0x160 tcp_recvmsg_locked+0xce0/0x1130 tcp_recvmsg+0xeb/0x300 inet_recvmsg+0xcf/0x3a0 sock_recvmsg+0xea/0x100 cifs_readv_from_socket+0x3a6/0x4d0 [cifs] cifs_read_iter_from_socket+0xdd/0x130 [cifs] cifs_readv_receive+0xaad/0xb10 [cifs] cifs_demultiplex_thread+0x1148/0x1740 [cifs] kthread+0x1cf/0x210 A flaw was found in the Linux kernel's network file system (netfs).
High [CVE-2026-64048] reject CHID-0 ACCEPT that matches an empty ism_dev slot
In the Linux kernel, the following vulnerability has been resolved: net/smc: reject CHID-0 ACCEPT that matches an empty ism_dev slot On the SMC-D client, slot 0 of ini->ism_dev[]/ini->ism_chid[] is reserved for an SMC-Dv1 device. smc_find_ism_v2_device_clnt() populates V2 entries starting at index 1, so when no V1 device is selected slot 0 is left in its kzalloc()'ed state with ism_dev[0] == NULL and ism_chid[0] == 0. smc_v2_determine_accepted_chid() then matches the peer's CHID against the array starting from index 0 using the CHID alone. A malicious peer replying to a SMC-Dv2-only proposal with d1.chid == 0 matches the empty slot, ini->ism_selected becomes 0, and the subsequent ism_dev[0]->lgr_lock dereference in smc_conn_create() faults at offsetof(struct smcd_dev, lgr_lock) == 0x68: BUG: KASAN: null-ptr-deref in _raw_spin_lock_bh+0x79/0xe0 Write of size 4 at addr 0000000000000068 by task exploit/144 Call Trace: _raw_spin_lock_bh smc_conn_create (net/smc/smc_core.c:1997) __smc_connect (net/smc/af_smc.c:1447) smc_connect (net/smc/af_smc.c:1720) __sys_connect __x64_sys_connect do_syscall_64 Require ism_dev[i] to be non-NULL before accepting a CHID match. A flaw was found in the Linux kernel's Server-Message-Block Direct (SMC-D) client. A remote attacker can exploit this vulnerability by sending a specially crafted SMC-Dv2 proposal with a Channel Identifier (CHID) of 0.
High [CVE-2026-64115] fix UAF when peer resets connection during handshake
In the Linux kernel, the following vulnerability has been resolved: vsock/vmci: fix UAF when peer resets connection during handshake vmci_transport_recv_connecting_server() returned err = 0 for a peer RST in its default switch arm: err = pkt->type == VMCI_TRANSPORT_PACKET_TYPE_RST? 0: -EINVAL; That made vmci_transport_recv_listen() skip vsock_remove_pending(), leaving the pending socket on the listener's pending_links with sk_state = TCP_CLOSE while destroy: still dropped the explicit reference taken before schedule_delayed_work(). One second later vsock_pending_work() observed is_pending=true and performed full cleanup: vsock_remove_pending() then the two trailing sock_put(sk) calls -- the first reached refcount 0 and __sk_freed the socket, and the second wrote into the freed object: BUG: KASAN: slab-use-after-free in refcount_warn_saturate Write of size 4 at addr ffff88800b1cac80 by task kworker Workqueue: events vsock_pending_work Treat peer RST like any other unexpected packet type (err = -EINVAL). All destroy: arms now return err 0/100 patched. A remote attacker could exploit a Use-After-Free (UAF) vulnerability when a peer resets a connection during the handshake process. This occurs because the system incorrectly handles…
High [CVE-2026-64175] stop TX during firmware restart
In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mld: stop TX during firmware restart When iwlwifi firmware crashes (e.g., NMI_INTERRUPT_UNKNOWN on Intel BE201/Wi-Fi 7), iwl_mld_nic_error() sets mld->fw_status.in_hw_restart to true. However, iwl_mld_tx_from_txq() does not check this flag before dequeuing frames from mac80211 and pushing them to the transport layer. Since the firmware is dead, iwl_trans_tx() returns -EIO for each frame, which then gets freed immediately. Under high-throughput conditions (e.g., Tailscale UDP traffic or active SSH sessions), this creates a tight dequeue-send-fail-free loop that wastes CPU cycles and generates rapid skb allocation churn, leading to memory pressure from slab fragmentation. The RX path already has this guard (iwl_mld_rx_mpdu checks in_hw_restart at rx.c:1906), and so does the TXQ allocation worker (iwl_mld_add_txqs_wk at tx.c:156). Add the same guard to iwl_mld_tx_from_txq() to stop all TX during firmware restart. Frames left in mac80211's TXQs are naturally drained after restart completes, when queue reallocation triggers iwl_mld_tx_from_txq() via iwl_mld_add_txq_list(), or when new upper-layer traffic invokes wake_tx_queue. Tested on ASUS Zenbook 14 UX3405CA with Intel BE201 (Wi-Fi 7) on kernel 6.19.5 where the firmware crashes approximately every 10-15 minutes under Tailscale traffic.
High [CVE-2026-64119] use list_del_rcu in l2tp_session_unhash
In the Linux kernel, the following vulnerability has been resolved: l2tp: use list_del_rcu in l2tp_session_unhash An unprivileged local user can pin a host CPU indefinitely in l2tp_session_get_by_ifname() by issuing L2TP_CMD_SESSION_GET on L2TP_ATTR_IFNAME concurrently with L2TP_CMD_SESSION_CREATE and L2TP_CMD_SESSION_DELETE on the same tunnel. All three commands take GENL_UNS_ADMIN_PERM, so CAP_NET_ADMIN in the netns user namespace suffices; on any host that has l2tp_core loaded the trigger is reachable from a standard `unshare -Urn` sandbox. l2tp_session_unhash() removes a session from tunnel->session_list with list_del_init(), but that list is walked by l2tp_session_get_by_ifname() with list_for_each_entry_rcu() under rcu_read_lock_bh(). list_del_init() leaves the deleted entry's next/prev self-pointing; a reader that has loaded the entry and then advances pos->list.next reads &session->list, container_of()s back to the same session, and list_for_each_entry_rcu() never reaches the list head. The CPU stays in strcmp() inside the walker, with BH and preemption disabled, so RCU grace periods on the host stall behind it and the wedged thread cannot be killed (SIGKILL is delivered on syscall return). Affected products named by the advisory: Red Hat Enterprise Linux 10; Red Hat package: kernel.
High [CVE-2026-64041] fix possible buffer overflow
In the Linux kernel, the following vulnerability has been resolved: ASoC: codecs: fs210x: fix possible buffer overflow In fs210x_effect_scene_info(), a string was copied like this: strscpy(DST, SRC, strlen(SRC) + 1); A buffer overflow would happen if strlen(SRC) >= sizeof(DST). Actually, strscpy() must be used this way: strscpy(DST, SRC, sizeof(DST)); strscpy(DST, SRC); // defaults to sizeof(DST) An incorrect use of the `strscpy` function in `fs210x_effect_scene_info()` can lead to a buffer overflow. This occurs when a string is copied without proper size validation, potentially allowing a local attacker to cause a denial of service or information disclosure. Red Hat severity: Moderate — CVSS 7 (CVSS:3.1/AV:L/AC:H/PR:L/UI:N/S:U/C:H/I:H/A:H). Weakness: CWE-120. Affected Red Hat products: Red Hat Enterprise Linux 10. Red Hat does not currently list a fixing RHSA for this CVE. Affected products named by the advisory: Red Hat package: kernel.
High [CVE-2026-64071] fix use-after-free in nvme_free_host_mem
In the Linux kernel, the following vulnerability has been resolved: nvme-pci: fix use-after-free in nvme_free_host_mem() nvme_free_host_mem() frees dev->hmb_sgt via dma_free_noncontiguous() but never clears the pointer afterward. This leads to a use-after-free if nvme_free_host_mem() is called twice in the same error path. This is reproducible on Thunderbolt-attached NVMe devices (e.g., OWC Envoy Express behind a Dell WD22TB4 dock) where the device intermittently returns I/O errors during HMB setup due to PCIe link instability. BUG: kernel NULL pointer dereference, address: 0000000000000010 RIP: 0010:iommu_dma_free_noncontiguous+0x22/0x80 Call Trace: dma_free_noncontiguous+0x3b/0x130 nvme_free_host_mem+0x30/0xf0 [nvme] nvme_probe.cold+0xcc/0x275 [nvme] local_pci_probe+0x43/0xa0 pci_device_probe+0xeea/0x290 really_probe+0xf9/0x3b0 __driver_probe_device+0x8b/0x170 driver_probe_device+0x24/0xd0 __driver_attach_async_helper+0x6b/0x110 async_run_entry_fn+0x37/0x170 process_one_work+0x1ac/0x3d0 worker_thread+0x1b8/0x360 kthread+0xf7/0x130 ret_from_fork+0x2d8/0x3a0 ret_from_fork_asm+0x1a/0x30 Fix this by setting dev->hmb_sgt to NULL after freeing it, so the second call takes the multi-descriptor path which safely handles the already-cleaned-up state. A flaw was found in the Linux kernel's NVMe over PCI Express (NVMe-PCIe) driver.
High [CVE-2026-64051] Add overflow check to remap_pfn_range during mmap
In the Linux kernel, the following vulnerability has been resolved: accel/qaic: Add overflow check to remap_pfn_range during mmap The call to remap_pfn_range in qaic_gem_object_mmap is susceptible to (re)mapping beyond the VMA if the BO is too large. This can cause use after free issues when munmap() unmaps only the VMA region and not the additional mappings. To prevent this, check the remaining size of the VMA before remapping and truncate the remapped length if sg->length is too large. [jhugo: fix braces from checkpatch --strict] This vulnerability allows for memory to be mapped beyond its intended boundaries during certain memory allocation operations. A local attacker could exploit this flaw, leading to a use-after-free condition. This could potentially result in privilege escalation or a denial of service. Red Hat severity: Important — CVSS 7 (CVSS:3.1/AV:L/AC:H/PR:L/UI:N/S:U/C:H/I:H/A:H). Weakness: CWE-787. Affected Red Hat products: Red Hat Enterprise Linux 10. Red Hat does not currently list a fixing RHSA for this CVE. Affected products named by the advisory: Red Hat package: kernel.
High [CVE-2026-64109] Fix UAF read of tail->len in unix_stream_data_wait
In the Linux kernel, the following vulnerability has been resolved: af_unix: Fix UAF read of tail->len in unix_stream_data_wait() unix_stream_data_wait() does skb_peek_tail(&sk->sk_receive_queue) without holding any lock that prevents SKBs on that queue from being dequeued and freed. This has been the case since commit 79f632c71bea ("unix/stream: fix peeking with an offset larger than data in queue"). The first consequence of this is that the pointer comparison `tail!= last` can be false even if `last` semantically refers to an already-freed SKB while `tail` is a new SKB allocated at the same address; which can cause unix_stream_data_wait() to wrongly keep blocking after new data has arrived, but only in a weird scenario where a peeking recv() and a normal recv() on the same socket are racing, which is probably not a real problem. Affected products named by the advisory: Red Hat Enterprise Linux 10; Red Hat Enterprise Linux 6; Red Hat Enterprise Linux 7; Red Hat Enterprise Linux 8; and 2 more.
High [CVE-2026-64132] refresh hdr pointer before ioam6_event
In the Linux kernel, the following vulnerability has been resolved: ipv6: ioam: refresh hdr pointer before ioam6_event() Reported by Sashiko: In ipv6_hop_ioam(), the hdr pointer is initialized to point into the skb's linear data buffer. Later, the code calls skb_ensure_writable(), which might reallocate the buffer: if (skb_ensure_writable(skb, optoff + 2 + hdr->opt_len)) goto drop; /* Trace pointer may have changed */ trace = (struct ioam6_trace_hdr *)(skb_network_header(skb) + optoff + sizeof(*hdr)); ioam6_fill_trace_data(skb, ns, trace, true); ioam6_event(IOAM6_EVENT_TRACE, dev_net(skb->dev), GFP_ATOMIC, (void *)trace, hdr->opt_len - 2); If the skb is cloned or lacks sufficient linear headroom, skb_ensure_writable() will invoke pskb_expand_head(), which reallocates the skb's data buffer and frees the old one, invalidating pointers to it. While the code recalculates the trace pointer immediately after the call to skb_ensure_writable(), it fails to recalculate the hdr pointer. This patch fixes the above by recalculating the hdr pointer before passing hdr->opt_len to ioam6_event(), so that we avoid any UaF. A flaw was found in the Linux kernel's IPv6 In-situ Operations, Administration, and Maintenance (IOAM) component. This vulnerability, a use-after-free, occurs when the kernel fails to correctly update a pointer after reallocating a network packet's buffer.